Conferences

Tabassum, N., Nahed, N., Ahsan, R. and Khan, A. (2019), “Experimental Investigation and Comparison of AISC and EUROCODE for Built-Up CFT Columns Under Concentric and Eccentric Loading,” Proceedings of the 2^nd International Conference on Structural Engineering Research (iCSER2019) 4^th GCSTMR World Congress, Dhaka, January 19-22, pp 112-117
Nishat, T. and Ahsan, R. (2019), “A Comparative Analysis of the Sensitivity of Optimum Design Parameters of Post-tensioned Pre-stressed I-girder Bridge at Varied Steel Cost,” Proceedings of the 2^nd International Conference on Structural Engineering Research (iCSER2019) 4^th GCSTMR World Congress, Dhaka, January 19-22, pp 176-181
Islam, M. A. and Ahsan, R. (2019), “Performance of unreinforced masonry walls in shaking table test,” Proceedings of International Conference on Disaster Risk Management, BUET-JIDPUS, Dhaka, January 12-14, pp 68-73
Islam, M. A., Barua, U., Akter, T., Ahsan, R., Akther, M. S., Islam, I. and Ansary, M. A. (2019), “Structural vulnerability and social readiness in Mymensingh, Bangladesh,” Proceedings of International Conference on Disaster Risk Management, BUET-JIDPUS, Dhaka, January 12-14, pp 74-79
Zaman, M. W., Ali, M. M., Mita, K. S., Azad A. A., Akter, M., Ahsan, R., Haque, A. and Rahman, M. (2019), “Structural response of coastal wooden infrastructure to cyclonic wind and surge induced thrust force,” Proceedings of International Conference on Disaster Risk Management, BUET-JIDPUS, Dhaka, January 12-14, pp 89-94
Hossain, M. S., Khan, Y. A. and Ahsan, R. (2019), “Cyclic load test on beam-column behavior of portal frame strengthening by micro-concrete,” Proceedings of International Conference on Disaster Risk Management, BUET-JIDPUS, Dhaka, January 12-14, pp 95-101
Akter, T., Barua, U., Islam, M. A., Islam, I., Akther, M. S., Ansary, M. A. and Ahsan, R. (2019), “Understanding social vulnerability of a community for earthquake: a study on ward no. 14, Mymensingh municipality, Bangladesh,” Proceedings of International Conference on Disaster Risk Management, BUET-JIDPUS, Dhaka, January 12-14, pp 275-281
Barua, U., Akter, T., Islam, M. A, Akhter, M. S., Islam, I., Ahsan, R. and Ansary, M. A. (2019), “Community participation in earthquake contingency planning: an experience from ward no. 14, Mymensingh municipality, Bangladesh,” Proceedings of International Conference on Disaster Risk Management, BUET-JIDPUS, Dhaka, January 12-14, pp 401-408
Asif, M. M., Alam, M. Z. and Ahsan, R. (2019), “Capacity of roof cladding of rural housing against blowing due to storm wind,” Proceedings of International Conference on Disaster Risk Management, BUET-JIDPUS, Dhaka, January 12-14, pp 506-510
Rahman, R. and Ahsan, R. (2018), “Evaluation of Design Parameters of Near Embankment Underground Tunnel Structure by Numerical Analysis of a 2D Plain Strain Model,” GeoMeast2018, Cairo, accepted for publication.
Hussaini, T. M., Anam, M. M., Islam, K., Ahmed, K. S. and Ahsan, R. (2018), “New dynamic testing facility at BUET-JIDPUS: Cyclic loading of 1/3 scale damaged RC column retrofitted with externally wrapped CFRP sheets,” Fifteenth International Conference on Structural and Geotechnical Engineering, Advances In Construction Techniques, Ain Shams University
Ahasan, H., Khan, S., Hassan, A., Ahsan, R. and Ansary M. A., (2017), “Use of Jet Grouting in Retrofitting of a RMG Factory Building in Chittagong, Bangladesh,” Proceedings of Grouting 2017: Grouting, Deep Mixing, and Diaphragm Walls, Honolulu, Oahu, Hawai, USA, July 9-12,
Zahura, F. T. and Ahsan, R. (2016), " Numerical Simulation of Punching Shear of Flat Plates with Low Reinforcement," ICSCE 2016 : 18th International Conference on Structural and Construction Engineering. World Academy of Science, Engineering And Technology (WASET), Istambul, Turkey, Jul 21-22,2016.
Rahman, M. S., Begum, M. and Ahsan, R. (2016), "Comparison Between Experimental and Numerical Studies of Fully Encased Composite Columns," accepted for publication in ICCSEE-2016 18th Int. Conf. on Civil, Structural and Earthquake Engineering. World Academy of Science, Engineering And Technology (WASET), Toronto, Canada, Jun 13-14,2016.
Ahmed, S., Hossen, M. B. and Ahsan, R. (2016), “Production of GI wire fiber reinforced micro-concrete,” BUET Anwar Ispat 1^st Bangladesh Civil Engineering Summit 2016, Dhaka.
Ahsan, R. (2015), “Cyclic Tests on Different Schemes of Retrofitting of Reinforced Concrete Beam-Column Interior Joints,” CICM 2015, First International Conference on Advances in Civil Infrastructure and Construction Materials, MIST, Dhaka, Bangladesh, 14–15 December 2015.
Ahmed, S., Hasan, R. and Ahsan, R. (2015), “Production of Microconrete using Indigenous Materials,” CICM 2015, First International Conference on Advances in Civil Infrastructure and Construction Materials, MIST, Dhaka, Bangladesh, 14–15 December 2015.
Rahman, M. S., Begum, M. and Ahsan, R. (2015), " Nonlinear finite element analysis of Fully encased composite columns and review of codes," CICM 2015, First International Conference on Advances in Civil Infrastructure and Construction Materials, MIST, Dhaka, Bangladesh, 14–15 December 2015.
Rahman, M. S., Begum, M. and Ahsan, R. (2015), " Behaviour and Strength of Fully Encased Composite Columns," International Conference on Recent Innovation in Civil Engineering for Sustainable Development (IICSD-2015), Department of Civil Engineering, DUET - Gazipur, Bangladesh, December 2015.
Amin, A. F. M. S., Amanat, K. M., Ahsan, R. and Rahmatullah, R. (2015), “Renovation of two century-old steel truss railway bridges to increase the vertical clearance,” IABSE-JSCE Conference on Advances in Bridge Engineering-III, August 2015, Dhaka, pp 561-568.
Rashed, M. G., Ahsan, R. and Jumbo, F. S. (2013), “Vibration Control of a Frame Structure Using Pulsed Current Activated Shape Memory Alloy Braces,” International Conference on Earthquake Engineering (SE-50EEE) At: Skopje, Macedonia
Rashed, M. G., Ahsan, R. and Parnell, T. K. (2013), “Numerical Simulation of Seismic Response Control of Frame Structure Using High-Temperature Shape Memory Alloy Wire,” International Conference on Earthquake Engineering (SE-50EEE) At: Skopje, Macedonia
Rashed, M. G. and Ahsan, R. (2013), “A Simple Approach in Finite Element Simulation of Shape Memory Alloy Brace Having Multiple Wires,” International Conference on Earthquake Engineering (SE-50EEE) At: Skopje, Macedonia
Rashed, M. G., Ahsan, R. and Islam, B. (2012), “Civil Engineering Application of Shape Memory Alloys,” First International Conference on Advances in Civil l3Engineering, Chittagong, December.
Islam, B., Ahsan, R. and Rashed, M. G. (2012), “Retrofit Techniques of Structures Associated with Soft Story,” First International Conference on Advances in Civil Engineering, Chittagong, December.
Islam, B. and Ahsan, R. (2012), “Optimization of Tuned Mass Damper Parameters using Evolutionary Operation Algorithm,” 15 World Conference on Earthquake Engineering, Lisbon, September.
Rashed, M. G., Ahsan, R. and Chowdhury, S. R.(2012), “Numerical modeling of concrete tensile strength test by wrapping scripting language with compiled library,” International Journal of Computer Applications, Vol. 40(14), pp. 34-38.
Mustafy, T., Islam, K. and Ahsan, R. (2012), “Finite Element Analysis of Rectangular Hollow Section Bonded with CFRP”, Proceedings of the 12th Pan American Congress of Applied Mechanics (PACAM XII), January 2-6, 2012, Port of Spain, Trinidad.
Islam, B., Ahsan, R. and Ansary, M. A. (2011), “Bridge Deck Condition Assessment by Ground Penetrating Radar – A Case Study in Bangladesh,” New Technologies for Urban Safety of Megacities in Asia (USMCA) Symposium, Chiang Mai, October.
Mustafy, T., Islam, K. and Ahsan, R. (2011), “Seismic Response Analysis of Bridge with Different Isolators”, Fourth Structural Engineering World Congress (SEWC-2011), ASCE, April 4-6, 2011, Milano, Italy (10 pp. on CD-ROM Edition).
Islakm, K., Mustafy, T. and Ahsan, R. (2011), “Seismic Performance of a Multi-span Continuous Base-isolated Bridge with Different Isolation Systems”, The 43rd Symposium on Engineering Geology and Geotechnical Engineering(EGGE), March 23-25,2011, Las Vegas, Nevada, USA (13 pp. on CD-ROM Edition).
Mustafy,T, Ahsan,R (2010), “FE Modeling and Experimental Verification of a CFRP strengthened steel section subjected to transverse end bearing force”, Proceedings of IABSE-JSCE Joint Conference on Advances in Bridge Engineering-II,August 2010, Dhaka, Bangladesh, pp. 512-518.
Ahsan, R. and Reza, S.M. (2010), “Dynamic behaviour of the Jamuna Multi-Purpose Bridge considering soil-structure interaction,” Proceedings of the 9^th US National and 10^th Canadian Conference on Earthquake Engineering, Toronto.
S. M. Reza, Ahsan, R. (2010), Dynamic behaviour of the Jamuna multi-purpose bridge considering different scour depth. IABSE-JSCE Joint Conference on Advances in Bridge Engineering-II, Dhaka, Bangladesh, August 8-10, 2010.
Ahsan, R., Hasan, M.M. and Reza, S.M. (2010), “Modal analysis of the Jamuna Multi-Purpose Bridge considering soil-structure interaction,” Proceedings of the 3^rd International Earthquake Symposium, Bangladesh, Dhaka, 373-379.
Islam, B., Ahsan, R., Reza, S.M. (2009), “Dynamic stiffness parameters for hollow steel piles for soil-structure interaction,” Proceedings of the Bangladesh Geotechnical Conference 2009, Dhaka, 58-64.
Rahman, A. Z. M. M., Ahsan, R., Ansary, M. A., Al-Hussaini, T. M. and Moni, M. (2009), “Monitoring dynamic behaviour of the Jamuna Multipurpose Bridge,” Proceedings of the 7th Asia Pacific Structural Engineering and Construction Conference (APSEC 2009) and 2nd European Asian Civil Engineering Forum (EACEF 2009), Langkawi, 450-456.
Hassan, A., Ahsan, R., Hossain, B.M.T.A., Ahsan, M. R. (2009), "Spatial distribution of existing cyclone shelters for tsunami and storm surge preparedness," Proceedings of the International Workshop on Tsunami and Storm Surge Hazard Assessment and Management for Bangladesh, Ministry of Food and Disaster Management, Comprehensive Disaster Management Programme (CDMP), Government of Bangladesh, pp 81-89.
Bhuiyan, M. A. H., Ahsan, R., Ahmed, M. M. Z. (2009), "Structural Strength Analysis of Infrastructure in the Coastal Region of Bangladesh," Proceedings of the International Workshop on Tsunami and Storm Surge Hazard Assessment and Management for Bangladesh, Ministry of Food and Disaster Management, Comprehensive Disaster Management Programme (CDMP), Government of Bangladesh, pp 90-96.
Rahman, A. Z. M. M., Ahsan, R., Al-Hussaini, T. M., Ansary, M. A. and Moni, M. (2008), “Dynamic performance monitoring of the Jamuna Multipurpose Bridge,” International Seminar on Latest Trends in Construction of Bridges, Indian Institute of Bridge Engineers, New Delhi, pp. 136-142.
Das, P. P. and Ahsan, R. (2007), “Performance based analysis of an inelastic unbraced steel frame with semirigid connections,” 2^nd International Earthquake Symposium Bangladesh, Dhaka, 113-125.
Ahsan, R., Johasson, J., Konagai, K. and Tanaka, H. (2007), “Analysis of axial vibration of piles in layered soil media and application to batter piles,” International Conference on New Technologies for Urban Safety of Mega-Cities in Asia, Dhaka, December.
Reza, S. M., Ahsan, R. and Ansary, M. A. (2007), “Effect of infills on the dynamic behaviour of RC Frames,” International Conference on New Technologies for Urban Safety of Mega-Cities in Asia, Dhaka, December.
Ahsan, R., Ansary, M. A., Al-Hussini T. M. and Rahman, S. Z. (2007), “Structural Identification of the Jamuna Multipurpose Bridge,” Proceedings on the Third International Conference on Structural Engineering, Mechanics and Computation, Capetown, September.
Zakaria, A. M., Al-Hussaini, T. M., Ahsan, R. and Islam M. K. (2006), “Seismic risk reduction in Bangladesh: The network approach,” Proceedings of National Conference, Civil Engineering: Meeting the Challenges of Tomorrow, Punjab, India, November, 91-95.
Ahmed, M. Z., Ahsan, R. and Dorka, U. E. (2005), “A possibility of using HYDE systems for seismic safety of soft-storey buildings in Bangladesh,” Proceedings of First Bangladesh Earthquake Symposium (BES – 1), Dhaka, 163-170.
Rahman, S. Z., Das, P. P. and Ahsan, R. (2005), “Dynamic Analysis of semi-rigid 2D steel frames under monotonic loading,” Proceedings of First Bangladesh Earthquake Symposium (BES – 1), Dhaka, 195-202.
Ahsan, R., Al-Hussaini, T. M., Ansary, M. A. and Rahman, M. M. (2005), “Identification of dynamic parameters of the Jamuna Multipurpose Bridge in ambient transverse vibration,” Proceedings of the Japan-Bangladesh Joint Seminar on Advances in Bridge Engineering, Dhaka, 1-12.
Ahsan, R. and Siddiquee, M.S.A. (2003), “Simulation of cyclic stress-strain behavior of sand”, Proceedings of 12^th Asian Regional Conference on Soil Mechanics and Geotechnical Engineering, Singapore,BD-05.
Ahsan, R., Ahmed, I. and Ahmed, B. (2003), “Secant stiffness of semi-rigid steel frames,” Proceedings of the Second Annual Paper Meet and International Conference on Civil Engineering organised by Institution of Engineers, Bangladesh and Bangladesh University of Engineering and Technology, 319-329.
Konagai, K., Ahsan, R. and Maruyama, D. (2000), “Simulation of energy influx and efflux through soil-structure interface,” Proceedings of 12^th World Conference of Earthquake Engineering, Auckland, New Zealand, 1334/5/A.

Page updated

Google Sites

Report abuse